RKI Instruments, Inc.www.rkiinstruments.comBeacon 110 Rig MonitorOperator’s ManualPart Number: 71-0232RKRevision: CReleased: 9/30/14
5 Beacon 110 Rig Monitor Operator’s ManualH2S Detector and CableThe H2S detector consists of a junction box with a mounting bracket, the detector, an
Beacon 110 Rig Monitor Operator’s Manual 6Figure 3: H2S Detector Component LocationThe sensor is secured within the sensor housing by four pins. Thro
7 Beacon 110 Rig Monitor Operator’s ManualInternal DescriptionThis section describes the internal components of the Beacon 110 Rig MonitorPower Conve
Beacon 110 Rig Monitor Operator’s Manual 8• Detector/Transmitter Terminal Strips. Three adjacent terminal strips are located along the right side of
9 Beacon 110 Rig Monitor Operator’s ManualFigure 4: Control PCB Component LocationLCD DisplayThe LCD display is located at the top of the control PCB
Beacon 110 Rig Monitor Operator’s Manual 10Status LEDsThe Rig Monitor includes three active status LEDs that are located above the display (see Figur
11 Beacon 110 Rig Monitor Operator’s ManualChapter 3: Installation & StartupOverviewThis chapter describes procedures to mount the Beacon 110 Rig
Beacon 110 Rig Monitor Operator’s Manual 121. Select the mounting site. When you select the mounting site consider the following factors:• Is a DC po
13 Beacon 110 Rig Monitor Operator’s ManualWiring the Beacon 110 Rig MonitorThis section describes procedures to connect external alarm(s) and a reco
Beacon 110 Rig Monitor Operator’s Manual 14WARNING: Make all connections to the Beacon 110 Rig Monitor before you plug in or turn on the DC power sou
Beacon 110 Rig Monitor Operator’s ManualWARNINGRead and understand this instruction manual before operating instrument. Improper use of the rig monit
15 Beacon 110 Rig Monitor Operator’s ManualConnecting RecordersPerform the following procedure to connect an analog signal recording device to the Ri
Beacon 110 Rig Monitor Operator’s Manual 16Start UpIntroducing Incoming PowerPerform the following procedure to place the Rig Monitor into normal ope
17 Beacon 110 Rig Monitor Operator’s ManualChapter 4: OperationOverviewThis chapter describes the Beacon 110 Rig Monitor in normal operation. This ch
Beacon 110 Rig Monitor Operator’s Manual 184 - 20 mA Signal Output OperationThe output at the 4 - 20 mA output terminals is a 4 - 20 mA signal that i
19 Beacon 110 Rig Monitor Operator’s ManualAlarm IndicationsNOTE: The Beacon 110 Rig Monitor includes alarm on and alarm off delay settings for alarm
Beacon 110 Rig Monitor Operator’s Manual 20Alarm 1 ConditionAlarm 1 Condition IndicationsWhen the gas reading reaches the alarm 1 setpoint, the Rig M
21 Beacon 110 Rig Monitor Operator’s ManualResponding to an Alarm 2 Condition1. Follow your established procedure for a toxic gas condition.2. The al
Beacon 110 Rig Monitor Operator’s Manual 22Chapter 5: Configuration ModeOverviewThis chapter describes how to view and change Beacon 110 Rig Monitor
23 Beacon 110 Rig Monitor Operator’s ManualTable 6: Configuration ParametersParameter(Factory Set Value)DescriptionALARM-1 (10 ppm)The gas reading at
Beacon 110 Rig Monitor Operator’s Manual 244. When you have scrolled through all the adjustable parameters, SAVE IT? YES/NO appears on the display.5.
Beacon 110 Rig Monitor Operator’s ManualProduct WarrantyRKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in ma
25 Beacon 110 Rig Monitor Operator’s ManualChapter 6: MaintenanceOverviewThis chapter describes how to calibrate the Beacon 110 Rig Monitor using Cal
Beacon 110 Rig Monitor Operator’s Manual 26Calibration Program FlowFigure 10 below illustrates the general flow of the Calibration Program for a dir
27 Beacon 110 Rig Monitor Operator’s Manual1. While in normal operation, press and hold the UP/YES button for 5 seconds to enter Calibration Mode. Re
Beacon 110 Rig Monitor Operator’s Manual 28Setting the Response Reading1. Screw the regulator into the calibration gas cylinder.2. If you want to ski
29 Beacon 110 Rig Monitor Operator’s ManualAdjusting Strobe/Horn VolumeThe horn volume on the strobe/horn can be adjusted by doing the following:1. O
Beacon 110 Rig Monitor Operator’s Manual 307. Turn the Audio Select switch so that the selection arrow is pointing to the desired number.8. Place the
31 Beacon 110 Rig Monitor Operator’s Manualcap gasket.5. Unplug and remove the H2S sensor with the rubber boot and spacer attached.6. Remove the rubb
Beacon 110 Rig Monitor Operator’s Manual 32Preventive MaintenanceThis section describes a preventive maintenance schedule to ensure the optimum perfo
33 Beacon 110 Rig Monitor Operator’s ManualTroubleshootingThe troubleshooting guide describes symptoms, probable causes, and recommended action for p
Beacon 110 Rig Monitor Operator’s Manual 34Buzzer Not Working• The buzzer does not sound an audible alarm during alarm conditions.• The buzzer sounds
Beacon 110 Rig Monitor Operator’s ManualTable of ContentsChapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35 Beacon 110 Rig Monitor Operator’s ManualSlow or No Response/Difficult or Unable to Calibrate• Detector responds slowly or does not respond during
Beacon 110 Rig Monitor Operator’s Manual 36Parts ListTable 8 lists replacement parts and accessories for the Beacon 110 Rig Monitor.Table 8: Parts Li
37 Beacon 110 Rig Monitor Operator’s ManualAppendix A: Control Button Quick Reference GuideThe Beacon 110 Rig Monitor’s control buttons and reset swi
Beacon 110 Rig Monitor Operator’s ManualChapter 6: Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Beacon 110 Rig Monitor Operator’s ManualChapter 1: IntroductionOverviewThis chapter briefly describes the Beacon 110 Rig Monitor. This chapter also
Beacon 110 Rig Monitor Operator’s Manual 2SpecificationsTable 1 lists specifications for the Beacon 110 Rig Monitor.WARNING: When using the Beacon 11
3 Beacon 110 Rig Monitor Operator’s ManualChapter 2: DescriptionOverviewThis chapter describes external and internal components of the Beacon 110 Rig
Beacon 110 Rig Monitor Operator’s Manual 4External DescriptionThis section describes the housing and all external components of the Beacon 110 Rig Mo
Comments to this Manuals